Autoplane Technologies
Request a unit

How it works

Foam for conformity.
Steel for abrasive support.

Foam lets the head conform to the intended curve. A thin, continuous stainless-steel lamina supports the abrasive across small surface depressions, helping provide a cutting reference for raised areas. It is one connected steel layer with six dust-extraction ports, rather than separate support segments; continuous does not mean unperforated.

  1. Set up. Center the head on your 6-inch backing pad and align the abrasive with the jig.
  2. Work supported areas. Use even pressure and overlapping passes suited to the coating stage.
  3. Inspect as you go. Check contour, scratches and remaining material before continuing.

Inside the head

Four layers, bonded into one piece. Six dust ports run straight through all of them, so the head is extraction-ready.

SANDER SIDE ABRASIVE SIDE Dust extraction port Six, lined up through every layer Loop backing Mounts to your sander's hook pad Dense, fine-cell foam Lets the lamina take the contour Continuous stainless-steel lamina · stiffens when bent Hook face Takes any 6-inch hook-and-loop disc
Section view, not to scale; the continuous stainless-steel lamina is enlarged for identification. The six extraction ports pass through all four layers.

The mechanics

What changes when the steel bends.

The tradeoff on a curved panel

Rigid: long block or hard pad

Holds a flat face, so it levels. But a flat face can't conform to a curve: a hard pad flat-spots a crown and digs at edges, and getting a curve straight with a long block is slow, hard on the body and takes years to do well.

Soft: interface pad on a DA

Conforms to the curve and the texture. It refines the scratch pattern, but contour and texture still need their own inspection before the next coating.

What's on a panel, from big to small

ContourThe shape the panel is built with: its crown and curves.

What takes care of itPreserved. AutoPlane conforms to it.

6 in
Long-form wavinessWaves longer than the head can span.

What takes care of itGuide coat and light diagnostic long-block passes on filler and primer-surfacer, where contact suits the intended contour. Stop and assess persistent marks.

6 in
Short-form textureOrange peel, filler and primer texture, and small surface variations within the head’s span.

What takes care of itAutoPlane's main job. The bent steel layer spans surface depressions and supports cutting on raised areas.

Scratch patternThe fine grooves each grit leaves behind.

What takes care of itA suitable finer abrasive and a separate scratch-pattern inspection. Use the coating and abrasive instructions to choose each step.

Drawings exaggerated for clarity.

Curvature-activated stiffening · Patent Pending

Sanding pressure conforms it.
The bend stiffens it.

With even, supported pressure, the foam gives and the stainless lamina bends toward the contour. Keep the head supported and guide overlapping passes. In its bent state the lamina is stiffer than in its flat state, the same way a steel tape measure holds straight once it's curved across.

The design gives the face a cutting reference across small surface depressions while conforming to the intended contour. Use controlled passes, then inspect the contour, scratch pattern and remaining material before continuing.

Flat state Sags under its own weight end view Bent state (curved across) Holds straight: the bend makes it stiff
Curvature across a tape blade helps it resist bending along its length.

Same curved panel with short-form texture · Dashed line = true contour

Soft interface pad
  • — Conforms to surface depressions.
  • — Supports abrasive against raised and recessed areas alike. A finer scratch pattern does not, by itself, establish a level surface.
AutoPlane
  • — Supports cutting on raised areas (gold).
  • — Conforms to the intended contour and spans surface depressions. Use controlled passes and inspect texture, scratches and permitted film removal separately.

Illustration, not to scale. Texture exaggerated; lamina enlarged for the purpose of identification.

Filler & primer-surfacer

What guide coat tells you

A diagnostic check for shape before you decide what to cut next.

  1. Apply compatible guide coat. Use it on filler and primer-surfacer, including before the initial primer cut.
  2. Check with light long-block passes. Keep the block in appropriate contact with the intended contour.
  3. Read the remaining pattern. Stop and assess persistent marks rather than sanding until every mark disappears.

Inspect scratches separately. This long-block check is for filler and primer-surfacer, not clear.

What you're seeing How it shows What to do
Short-form texture Fine specks of guide coat left across the area. Stop and assess the pattern, contact and remaining material before choosing the next pass.
Long-form waviness Broad bands of guide coat wider than the head, or a long block rocks across the panel. Use light diagnostic block passes where contact suits the intended contour; assess before correcting.
Possible high spot or breakthrough Bare metal shows through in one small spot while the area around it still has guide coat. This pattern alone does not confirm the cause. Stop and assess shape, block contact and material condition before choosing a correction.
Possible low spot or contact issue One patch still holds guide coat after everything around it is clean. This pattern alone does not confirm the cause. Stop and assess shape, block contact and material condition before choosing a correction.

Where it works

Big panels, small repairs.

Use it anywhere the 6-inch head sits fully supported: full skims and small repairs alike. It blends in a straight, controlled line, so blends stay tight and the repair area stays small.

  1. 01 Doors The flat and gently crowned skin between the body lines.
  2. 02 Hoods Broad, low-crown panels, from full skims to small spot repairs.
  3. 03 Roofs Large, open, lightly curved panels where the head sits fully supported.
  4. 04 Open areas of quarters The open, supported sections of the quarter, away from tight curves and body lines.
  5. 05 Fenders The open face of the fender. Arch lips and tight returns stay hand-block work.

Tight curves, sharp transitions and body lines are still hand-block work. Keep the head off raised edges: that's where burn-through happens.

By phase

A sequence for each stage.

The grit sequences below are provided as exemplary. Follow the coating TDS and abrasive instructions for cure, compatibility, permitted film removal and the next coating.

Filler

Example: P80 on AutoPlane, then guide coat and a light P180 long-block diagnostic check. Stop and assess persistent marks. Refine with P180 on AutoPlane; add P320 only if the next coating requires it.

Primer

On cured primer-surfacer, guide coat before a permitted P400 AutoPlane cut. Recheck with guide coat and light P600 long-block passes. Stop and assess persistent marks, then refine with P600 on AutoPlane. P800 and the basecoat or sealer route depend on the coating TDS.

Clear

Start with the least aggressive suitable grade on cured clear. P1500 then P2000 on AutoPlane is one permitted-system example. Keep required film; inspect edges. Use 3000+ foam-backed refinement off AutoPlane, then buff and polish per the system. No long-block check.

Ready for the next step?